ابدأ بالتواصل مع الأشخاص وتبادل معارفك المهنية

أنشئ حسابًا أو سجّل الدخول للانضمام إلى مجتمعك المهني.

متابعة

If the depth of structural element is limited, then how is excessive share force be controlled?

user-image
تم إضافة السؤال من قبل Imran Ahmed , Manager-Planning & Delay Analyst , Nesma United Industries (NUI) Saudi Arabia
تاريخ النشر: 2016/07/23
Imran Ahmed
من قبل Imran Ahmed , Manager-Planning & Delay Analyst , Nesma United Industries (NUI) Saudi Arabia

If depth of structural element is limited, shear strength of structural elements can be increased by following ways.

1) By using steel of higher strength

2) By using concrete of higher strength

3) By increasing shear reinforcment e.g. reduce the spacing of strips near the support having maximum shear force in beam and columns. In slab and foundation, special reinforcement in zigzag shape near around the columns having maximum shear.

4) Provide shear joist or clomun drop to increse shear strenght of the element.

michael ibao
من قبل michael ibao , MACHINIST SUPERVISOR IN MOTORPOOL , somac contacting

You can apply post tensioning system to control the excessive shear force 

Rajesh Nataraj
من قبل Rajesh Nataraj , Senior Draftsman , DBB Contracting LLC

- Maximize the steel reinforcement .

GAMAL AL-SAYED HUSSEIN - PMP Certified
من قبل GAMAL AL-SAYED HUSSEIN - PMP Certified , Project Manager , Saudi Consulting Services (SAUDCONSULT)

you can control the shear force in this case by one of these ways:

- Designer can change the type of element from concrete to steel or PC or Prestressed or (Post-tensioned System)

- Maximize the width of the str. element with higher grade of concrete.

- Maximize the no. of stirrups .

- Maximize the steel reinforcement .

- use special additives on the concrete

-you can support this element by steel plates or similer on the shear areas especially if this element already poured>

 

Finally , the designer and the Site Engineer can take the best action according Project Specs and the detailed information .

 

Thanks,

Noorul Ameen K T
من قبل Noorul Ameen K T , Assistant Engineer , Spectrum Techno Consultant pvt Ltd

By increasing the grade of concrete we an improve shear capacity of concrete. same for other material also

Baker Dwekat
من قبل Baker Dwekat , Senior Project Engineer- Geotechnics , Byrnelooby Partners

Reinforcment should do the job , however one can increase the dimensions (width) or using high quality materials (Fc' , fy) to control the shear.

Excessive force in shear and flexure can be controlled by increasing width of the element,by adopting higher grade of concrete,by increasing reinforcement to maximum limit.also we can go for post tensioned concrete or composite sections.

Muhammad Ikraam Ashraf
من قبل Muhammad Ikraam Ashraf , Junior expert Engineer , National Engineering Services,Pakistan(NESPAK).

If the depth of structural element is limited, then changing width Controls excessive share force

 

Ahilan R
من قبل Ahilan R , Scientific Assistant-D , Nuclear Power Corporation of India Ltd (NPCIL)

Agree with Imran Ahmed  reply

 

NAGARAJ SELVARAJ
من قبل NAGARAJ SELVARAJ , structural design engineer , L&T

1) increasing width of the beam (or) member

Ahmed shah PMP
من قبل Ahmed shah PMP , Planning Engineer , ZKB Engineers & Constructors

Mr. Imran, the shear strength for a members subject to shear and  flexure is given by ACI as

so if depth is kept constant, the shear  strength can be increase by increasing width (in case of beam) or by using high strength concrete.

المزيد من الأسئلة المماثلة

هل تحتاج لمساعدة في كتابة سيرة ذاتية تحتوي على الكلمات الدلالية التي يبحث عنها أصحاب العمل؟