Start networking and exchanging professional insights

Register now or log in to join your professional community.

Follow

ما الإحتياطات العامة أثناء اللحام بالكهرباء؟ What are the general precautions during electric welding?

• يتم مد كابلات اللحام على حوامل مرتفعة عن الأرض ولا يتم مده على الأرض ((ok • عدم توصيل ماكينة اللحام بالكهرباء إلا بعد موافقة الإدارة الهندسية ((ok • ماكينات اللحام التي تعمل بالديزل لايتم تموينها أثناء اللحام ((ok • إحفظ كل أبواب لوحات التوزيع مغلقة أثناء تشغيل الماكينة • لا يتم ضبط التيار أثناء اللحام لأن ذلك قد يتلف مفتاح التحكم • نقطة الأرضي يجب أن تكون قريبة قدر المستطاع من نقطة اللحام ((ok • التأكد من حالة الكابلات والوصلات والعزل جيدا وأيضا حالة الغلاف الخارجي يجب أن يكون محكم ((ok • يجب الالتزام بمهمات الوقاية الشخصية ((ok • استخدام الكابلات المتوافقة مع حمل الماكينة ((ok • مد كابل اللحام ولا تعرضه للثني أو اللف ((ok • توصيل ماكينة اللحام بالأرضي ووضعها في مكان خالي من أي أبخرة ((ok • عدم وجود اى وصلات بالكابلات غير متطابقة لمتطلبات السلامة الكهربية. ((ok • The D-welding cables on pregnant women, up from the ground and is not for the Earth ((ok • Welding machine is not connected to electricity only after the approval of Engineering Management ((ok • Welding machines that diesel-powered for not taken تموينها during welding ((ok • Keep all doors closed distribution boards while the machine is running • Do not be adjusted during the welding current because it may damage the control key • ground point should be as close as possible from the point of welding ((ok • make sure the condition of the cables and connectors, good insulation and also the case of the outer shell must be airtight ((ok • Obey personal protective missions ((ok • Use cables are backward compatible with Carrying Machine ((ok • D welding cable and subjected to bending or twisting ((ok • Connect the machine welding Balerda and put it in a place free from any fumes ((ok • the absence of any links with cables is identical to the electrical safety requirements. ((ok

user-image
Question added by Deleted user
Date Posted: 2013/08/18
Ahmed Ali Mourad Zahran
by Ahmed Ali Mourad Zahran , online Training , RRC Health and Safety Training

بارك الله فيك 

بلال لكحل
by بلال لكحل , ضابط حماية مدنية , الحماية المدنية

توفير الحماية الفردية (ارتداء القفازات ، الخودة ، النظارات العازلة، حداء العمل )

توفير الحماية الجماعية (إبعاد و عزل كل خطر محتمل في محيط العمل)

ammar ahmed mohammed mohammed ahmed alagbsh
by ammar ahmed mohammed mohammed ahmed alagbsh , Senior Maintenance Engineer , E.Connect International For Electronic Technology Co

الاحتياطات العامة للسلامة فى اللحام

1- لا يقوم باللحام إلا الفنيون المؤهلون والمرخص لهم بذلك .

2 – يجب على فني اللحام ومساعده استخدام معـدات الحماية من بدله اللحام وحذاء السلامة والخوذة وواقيات العينين والقفازات وواقي الوجه .

 

3- احم المنطقة المجاورة من شرر اللحام باستخدام ساتر مناسب .

4- عدم القطع أو اللحام في الأجواء التي ينتشر فيها الغازات الهيدوكاربونية و الغبار أو عند هبوب رياح عالية السرعة.

5 – يجب تعيين مراقب الحريق عند القيام باللحام في منطقة يكون خطر نشوب الحريق فيها كبيرا استعداداً لأي طارئ، على أن يكون مزوداً بالمعدات اللازمة لمكافحة الحريق .

-6 يجب أن تكون كابلات ماكينة اللحام وتوصيلاتها نظيفة وذات عزل جيد وغير تالفة ومناسبة للحمل الكهربائي المستخدم في أعمال اللحام .

 

Mohamed Hebishy
by Mohamed Hebishy , safety officer , تقنيه الخرسانه

•يجب توصيل الجسم الخارجي لماكينة اللحام بالأرضEarthing ، ويتم ذلك بتوصيل ملقط الأرضي بطاولة اللحام أو بالمعدن المراد لحامه.•يتم استخدام معدات الوقاية الشخصية المناسبة وعلي وجه الخصوص واقيات العين ذات عدسات بفلاتر الخاصة وحسب قطر الإلكترود.•عند توصيل ماكينة اللحام ، يجب أخذ المتطلبات التالية فى الإعتبار:1-توصيل الجسم الخارجي للماكينة بالأرض.2-توصيل مفتاح قاطع للكهرباء بالقرب من ماكينة اللحام للإستعمال في حالات الطوارئ.3-وجود قاطع كهربائي فيوز(Fuse) أو قاطع للتيار (Circuit Breake

يحي كعبي
by يحي كعبي , مندوب حكومي , شركه الاهليه المتقدمه للتجاره

للحام بالاكسجين يكون عن طريق لمبه اللحام  ويكون حديد    او  نحاس     او  المونيوم

Mohamed Abdou
by Mohamed Abdou , Fire and Safety Operator , Qatar Petroleum

بالاضافه الى .فى لحام خطوط الغاز او البترول يجب 

1-يجب عزل الخط قبل وبعد اللحام او القطع isolation 

2-عمل درين للخط قبل عمليه الحام 

التاكد من ارتداء جميع المهمات الواقيه ( البدلة الواقيه - النظارة الواقيه - الخوذه - القفاز )

التاكد من خلو المكاان من اى مادة قابله للاشتعال

التاكد من عدم وجود احد بالمكان بدون مهمات واقيه على مقربه من العمل

التاكد من التزام العامل بجميع شروط الامان 

التاكد من  صلاحيه جميع الوصلات الكهربائيه

التاكد من احتمال القدرة للوحه الجهد المبذول

التاكد من صلاحيه العامل وتاهيله

Othman Ben Saad
by Othman Ben Saad , AIRCRAFT MAINTENEC ENGINEER , Libyan Air Lines الخطوط الجوية الليبية

لبس النظارات واستخدام الالكترود المناسب

Amr hamdy
by Amr hamdy , لحام كهرباء , حديد وصلب

اللحام بالكهرباء يكون بسلك عن طريق بنسه اللحام >يوجد لحام حديد لحام استلس استيل لحام المونيوم لحام نحاس لحام ظهر اللحام بالاكسجين يكون عن طريق لمبه اللحام ويكون حديد او نحاس او المونيوم ويوجد لحام بالكهرباء والغاز وهو لحام الارجون

شكرا اخي كان عندك نواقص لاكن اكملها مصطفى متولي و شكرا على المجهود الرائع و المعلومات القيمة تذكيرنا بها لاننا بشر ننسىء او نخطئ الكمال لله  

omasan omagbemi
by omasan omagbemi , HSE Inspector , Jolomi Engineering Services Limited

1.
PREVENTION OF ELECTRIC SHOCK All portable welding machines and generators will be positively earthed by a1m (39 inches) earthing stake manufactured from suitable material driven into the earth to a depth of at least300mm (12 inches). 
  All welding earths will be connected as close as possible to the workplace or area where the welding is taking place or to a common earth grid located and approved by the client. 
    Welding earths shall not, under any circumstances be connected to any scaffolding, scaffold component or rigging equipment. 
  Welding cables shall be kept dry and free from grease and oil to prevent breakdown of insulation. 
Cables with exposed bare conductors shall be replaced or discarded immediately. 
2.
All welding machine120/240V power outlets shall be protected by a core balanced earth leakage protection circuit breaker set to trip at30 milliamperes.
  3.All welding and associated equipment will be inspected on regular basis by designated competent persons.
It should also be inspected prior to start of work.
4.ROUTING OF CABLES, HOSES, ETC.
All welding electrical leads and compressor hoses shall be suspended by an approved means (not tied up with wire) at least2 m (6.5 feet) from the ground or working platform.
 If it is not practical to route leads or hoses overhead of a work / traffic area, leads and hoses will be routed under the platform to eliminate any tripping hazards. 
5.
THERMAL Burns of the skin from hot metal, or from handling hot objects such as tools, rods or the work may be effectively prevented by the use of protective clothing such as arm and leg guards, aprons, shirts and gauntlets. 
  6.
RADIANT Risk of burns from radiant energy to the unprotected skin of the welder (such as arms, neck, ears or face) is easily prevented by the wearing of protective clothing. 
The use of ultra-violet barrier creams (e.g.
Uvistat ointment) may also be considered in certain situations. 
  All personnel directly involved in welding and cutting should wear suitable flame-resistant protective clothing, in addition to safety boots, helmets, etc. 
Such clothing shall include but not be limited to:    • Leather jackets • Leather gauntlets / gloves • Flameproof or flame-retardant overalls. 
Note: Clothing made from standard grades of nylon and other man-made fibers are not recommended for protection against thermal or radiant burns 7.
 EYE PROTECTION:Use of standard approved eye protection is also recommended to prevent damage to the eyes.

Do you need help in adding the right keywords to your CV? Let our CV writing experts help you.