What is the SMD process in electronics circuit Design?

SMD process is related to SMT. SMD stands for Surface Mounted Device and SMT stands for Surface Mounted Technology. As the name indicates, the process by which the components are directly placed and mounted on the surface of the PCB is called the SMD process or Surface Mounted Device Process.

Surface-mount technology (SMT) is a method for producing electronic circuits in which the components are mounted or placed directly onto the surface of printedcircuit boards (PCBs). ... An SMT component is usually smaller than its through-hole counterpart because it has either smaller leads or no leads at all.

Virtually all of today's mass produced electronics hardware is manufactured using surface mount technology, SMD. The associated surface mount devices, SMDs provide many advantages over their leaded predecessors in terms of manufacture ability and often performance.

Any process done by SMD chip is a SMD process

       

• Home
• Antennas & propagation
• Cellular telecoms
• Circuit design
• Components
• Power management
• RF technology
• Test
• Wireless
• News
• Broadcast
• Embedded
• Design principles
• Distribution
• Formulae
• Manufacture
• Satellites
• Telecoms & networks
• Jobs

Electronic Components

 

What is SMT Surface Mount Technology - Tutorial

- an overview or tutorial about surface mount technology, SMT and surface mount devices SMDs

SMT Tutorial Includes

• SMT overview
• SMD component packages
• SMD resistor
• SMD resistor markings
• MELF SMD resistor
• SMD capacitor
• Quad Flat Package, QFP
• BGA, Ball Grid Array
• SMD PLCC

Virtually all of today's mass produced electronics hardware is manufactured using surface mount technology, SMT. The associated surface mount devices, SMDs provide many advantages over their leaded predecessors in terms of manufacturability and often performance.

It was not until the's that surface mount technology, SMT became widely used. Once SMT started to be used, the change from conventional leaded components to surface mount devices, SMDs took place quickly in view of the enormous gains that could be made using SMT.

 

 

Why SMT?

Mass produced electronic circuit boards need to be manufactured in a highly mechanised manner to ensure the lowest cost of manufacture. The traditional leaded electronic components do not lend themselves to this approach. Although some mechanisation was possible, component leads needed to be pre-formed. Also when the leads were inserted into boards automatically problems were often encountered as wires would often not fit properly slowing production rates considerably.

It was reasoned that the wires that had traditionally been used for connections were not actually needed for printed circuit board construction. Rather than having leads placed through holes, the components could be soldered onto pads on the board instead. This also saved creating the lead holes in the boards which added cost to the production of the bare PCBs.

 

Typical SMT board with transistors, and passive components

 

As the components were mounted on the surface of the board, rather than having connections that went through holes in the board, the new technology was called surface mount technology or SMT and the devices used were surface mount devices, SMDs. The idea for SMT was adopted very quickly because it enabled greater levels of mechanisation to be used, and it considerably saved on manufacturing costs.

To accommodate surface mount technology, SMT, a completely new set of components was needed. New SMT outlines were required, and often the same components, e.g. ICs were sold in both traditional leaded packages and SMT packages. Despite this, the gains of using SMT proved to be so large that it was adopted very quickly.

 

SMT board with typical IC packages

 

What are SMT components?

Surface mount devices, SMDs by their nature are very different to the traditional leaded components. They can be split into a number of categories:

• Passive SMDs:   There is quite a variety of different packages used for passive SMDs. However the majority of passive SMDs are either resistors or capacitors for which the package sizes are reasonably well standardised. Other components including coils, crystals and others tend to have more individual requirements and hence their own packages. Resistors and capacitors have a variety of package sizes. These have designations that include:,,,,, and. The figures refer to the dimensions in hundreds of an inch. In other words the measures hundreds by6 hundreds of an inch. The larger sizes such as and were some of the first that were used. They are not in widespread use now as much smaller components are generally required. However they may find use in applications where larger power levels are needed or where other considerations require the larger size. The connections to the printed circuit board are made through metallised areas at either end of the package.
• Transistors and diodes:   These components are often contained in a small plastic package. The connections are made via leads which emanate from the package and are bent so that they touch the board. Three leads are always used for these packages. In this way it is easy to identify which way round the device must go.
• Integrated circuits:   There is a variety of packages which are used for integrated circuits. The package used depends upon the level of interconnectivity required. Many chips like the simple logic chips may only require or pins, whereas other like the VLSI processors and associated chips can require up to or more. In view of the wide variation of requirements there is a number of different packages available. For the smaller chips, packages such as the SOIC (Small Outline Integrated Circuit) may be used. These are effectively the SMT version of the familiar DIL (Dual In Line) packages used for the familiar series logic chips. Additionally there are smaller versions including TSOP (Thin Small Outline Package) and SSOP (Shrink Small Outline Package). The VLSI chips require a different approach. Typically a package known as a quad flat pack is used. This has a square or rectangular footprint and has pins emanating on all four sides. Pins again are bent out of the package in what is termed a gull-wing formation so that they meet the board. The spacing of the pins is dependent upon the number of pins required. For some chips it may be as close as thousandths of an inch. Great care is required when packaging these chips and handling them as the pins are very easily bent. Other packages are also available. One known as a BGA (Ball Grid Array) is used in many applications. Instead of having the connections on the side of the package, they are underneath. The connection pads have balls of solder that melt during the soldering process, thereby making a good connection with the board and mechanically attaching it. As the whole of the underside of the package can be used, the pitch of the connections is wider and it is found to be much more reliable. A smaller version of the BGA, known as the microBGA is also being used for some ICs. As the name suggests it is a smaller version of the BGA.