كلما زادت طلبات التقديم التي ترسلينها، زادت فرصك في الحصول على وظيفة!

إليك لمحة عن معدل نشاط الباحثات عن عمل خلال الشهر الماضي:

عدد الفرص التي تم تصفحها

عدد الطلبات التي تم تقديمها

استمري في التصفح والتقديم لزيادة فرصك في الحصول على وظيفة!

هل تبحثين عن جهات توظيف لها سجل مثبت في دعم وتمكين النساء؟

اضغطي هنا لاكتشاف الفرص المتاحة الآن!
نُقدّر رأيكِ

ندعوكِ للمشاركة في استطلاع مصمّم لمساعدة الباحثين على فهم أفضل الطرق لربط الباحثات عن عمل بالوظائف التي يبحثن عنها.

هل ترغبين في المشاركة؟

في حال تم اختياركِ، سنتواصل معكِ عبر البريد الإلكتروني لتزويدكِ بالتفاصيل والتعليمات الخاصة بالمشاركة.

ستحصلين على مبلغ 7 دولارات مقابل إجابتك على الاستطلاع.


تم إلغاء حظر المستخدم بنجاح
شكراً لك، تم إرسال بلاغك وسيتم مراجعته قريباً.
https://bayt.page.link/qGcUHkg6nC2wBnHo8
العودة إلى نتائج البحث‎
Larsen & Toubro logo

Application Software Design Engineer

Larsen & Toubro
قبل 5 ساعات 2027/03/18 ·ينتهي التقديم خلال 119 يومًا
الهند
خدمات الدعم التجاري الأخرى
أنشئ تنبيهًا وظيفيًا لوظائف مشابهة

الوصف الوظيفي

Application Software Design Engineer — Power Electronics (Tier1)


Band


Tier1— Senior FW Engineer



Experience


5 to 12 years



Function


R&D — Power Electronics / Embedded Systems



Domain


DC-DC converters, chargers, inverters, motor controllers (EV / industrial power conversion)



Location


Bengaluru 



Role Summary


Designs and implements the application-layer software that sits above the low-level drivers and control loops on power converter platforms — state machines, sequencing logic, diagnostics, calibration/parameter management, and host/HMI communication. Works closely with the firmware and control teams to integrate application logic with the underlying RTOS, CAN/RS-485 stacks, and (where applicable) AUTOSAR software components, under guidance from senior engineers.


Key Responsibilities


  • Design and implement application-layer software on STM32, C2000-based converter platforms — system state machines (init/standby/run/fault), sequencing, and mode management
  • Translate functional/system requirements into application software design — flowcharts, state diagrams, interface specs
  • Implement fault detection, protection sequencing, and diagnostic logic that consumes outputs from the control-loop (PI/PID) and driver layers
  • Develop and maintain calibration/parameter management (configurable thresholds, lookup tables, EEPROM/flash-backed settings)
  • Implement application-side CAN (J1939/proprietary) and RS-485 (Modbus) message handling — signal packing/unpacking, timeouts, fault frames
  • Integrate application logic with the existing RTOS task structure (FreeRTOS) — task/queue/event design at the application layer
  • Where the platform uses AUTOSAR, implement and configure Application SWCs / RTE interfaces under senior guidance
  • Support UDS/diagnostic service implementation (DTC handling, session control) where applicable
  • Debug end-to-end system behavior using CAN analyzer, logic analyzer, and on-target debugging (JTAG/SWD)
  • Write unit/integration tests for application logic; participate in code reviews and MISRA-C cleanup
  • Support bench validation, HIL testing, and bring-up of new converter variants

Must-Have Skills


  • Experience: 2–5 years in embedded application/system software, ideally power electronics or motor-control adjacent
  • MCU platform: Solid hands-on with STM32, C2000; comfortable reading/working with STM32, C2000 code at the application/interface level
  • RTOS: Working knowledge of FreeRTOS or similar — tasks, queues, semaphores, event groups
  • Control-loop interfacing: Working understanding of PI/PID control outputs and how application logic sequences around them (not tuning ownership)
  • Protocols: Hands-on with CAN and RS-485/Modbus at the application/message-handling level
  • AUTOSAR: Familiarity with Application SWC / RTE concepts — coursework or project-level exposure is acceptable
  • State machines: Demonstrated experience designing and implementing state-machine-driven embedded application logic
  • Tools: Comfortable with CAN analyzer (PCAN/Vector), oscilloscope for cross-checking system behavior, JTAG/SWD debugging
  • Fundamentals: Strong C, structured design practices, and clear requirement-to-code traceability

Good-to-Have


  • Exposure to UDS/diagnostics (ISO 14229) and DTC management
  • Scripting (Python) for test automation, log parsing, or calibration tooling
  • Git, static analysis tools (Coverity/PC-lint), Jenkins/CI exposure
  • Exposure to Simulink/Embedded Coder or model-based application design
  • Prior work on chargers, inverters, or motor controllers in an EV/industrial setting

Qualification


B.E./B.Tech — Electronics, Electrical, Computer Science, Instrumentation, or related discipline


لقد تمت ترجمة هذا الإعلان الوظيفي بواسطة الذكاء الاصطناعي وقد يحتوي على بعض الاختلافات أو الأخطاء البسيطة.
هل أنت متأكد أنك تريد سحب طلب التقديم إلى هذه الوظيفة؟

لن يتم النظر في طلبك لهذة الوظيفة، وسيتم إزالته من البريد الوارد الخاص بصاحب العمل.